{$cfg_webname}
主页 > 机械机电 > 模具 >

花盘倒装式复合冲裁模的设计(含cad零件图和装配图)

来源:wenku168.com  资料编号:WK1687849 资料等级:★★★★★ %E8%B5%84%E6%96%99%E7%BC%96%E5%8F%B7%EF%BC%9AWK1687849
资料介绍

花盘倒装式复合冲裁模的设计(含cad零件图和装配图)(含选题审批表,任务书,中期检查表,论文说明书10000字,CAD图纸7张)
摘  要:采用弹压卸料的方式,弹压卸料具有结构简单,卸料效果好,等优点,适合任务所需冲裁模。冲孔废料采用自由掉落的方式,在凸凹模的下方开口,使冲裁废料自然掉出。工件从凸模与凹模之间卸料,采用弹簧卸料板,不但可以起到冲裁压边的作用,还可以工件卸料。落料后的条料也采用弹簧卸料板卸料,从凸凹模中卸出。
关键词:冲裁;冲裁模;弹簧;CAD;卸料;
 
The faceplate upside-down compound blandingdie
Abstract: adopting the method of leaned uploading,  which has the advantage with simple structure and good  effect of uploading and adjust to blankingdie. Punching waste take the method of free drop out to make the blanking waste drop out in a natural way at the down open of concave-convex pattern.The product unload between the punch pin and the blanking cavity die unloading, straight by a spring stripper plate, not only can play the role of press edge, still can upload the product.After dropping material strip material also use spring stripper plate unloading, discharged from concavo-convex models
Key words:blanding;blandingdie;spring;CAD;unload

花盘倒装式复合冲裁模制造简单、生产成本低,生产效率高,产品的制造周期段,在国内外的应用非常广泛。为了提高个人的实际能力,适应社会急需的有创新精神的应用型人才,选择了花盘倒装式复合冲裁模的设计。本花盘倒装式复合冲裁模采用普通冲裁,弹压卸料, 因冲裁工件形状复杂,采用倒装式复合模
 

花盘倒装式复合冲裁模的设计(含cad零件图和装配图)
花盘倒装式复合冲裁模的设计(含cad零件图和装配图)
花盘倒装式复合冲裁模的设计(含cad零件图和装配图)


目    录
    摘要……………………………………………………………………………………1
    关键词…………………………………………………………………………………1
    1前言…………………………………………………………………………………1
    2设计任务……………………………………………………………………………2
        2.1设计任务书 …………………………………………………………………2
        2.2设计任务…………………………………………………………………3
3 工艺方案的确定……………………………………………………………………3
    3.1零件的工艺分析……………………………………………………………3
    3.2 制定冲压工艺方案…………………………………………………………3
4 冲压工件的有关计算………………………………………………………………4
    4.1 排样方式的计算……………………………………………………………4
        4.1.1 排样…………………………………………………………………4
        4.1.2 搭边,条料宽度的计算…………………………………………4
    4.2 压力中心的计算……………………………………………………………6
    4.3 冲裁工艺力的计算…………………………………………………………8
5 冲裁模设计中的有关计算…………………………………………………………10
    5.1 冲裁间隙……………………………………………………………………10
    5.2 冲裁模刃口尺寸……………………………………………………………10
        5.2.1 落料模刃口尺寸的计算……………………………………………11
        5.2.2 冲孔模刃口尺寸的计算……………………………………………13
6 模具结构设计………………………………………………………………………15
    6.1模的结构尺寸………………………………………………………………15
        6.1.1冲孔凸模…………………………………………………………15
        6.1.2冲孔凹模……………………………………………………………16
        6.1.3落料凸模……………………………………………………………16
        6.1.4落料凹模……………………………………………………………18
     6.2凹模周界与模架设计………………………………………………………18
     6.3卸料板与固定板的选用……………………………………………………18
     6.4模具的闭合高度与压力机的选用…………………………………………18
     6.5导柱导套配合的选用………………………………………………………19
     6.6销钉的确定…………………………………………………………………20
         6.6.1挡料销与导料销……………………………………………………20
         6.6.2定位销………………………………………………………………20
     6.7螺钉的确定…………………………………………………………………20
     6.8弹簧的选择…………………………………………………………………21
     6.9模柄的选择…………………………………………………………………22
    7结论…………………………………………………………………………………22
    参考文献 ……………………………………………………………………………23
    致谢……………………………………………………………………………………23

推荐资料